background image

12 

+ supply 

CANH 

10 

Activity detection (low active) 

11 

GND 

12 

GND 

13 

GND 

14 

GND 

2.3 

EN norms 

Electromagnetic compatibility (EMC) 

The manufacturer confirms that the truck adheres to the limits for electromagnetic 

emissions  and  resistance  as  well  as  the  static  electricity  discharge  test  in 
accordance  with  EN  300330-1  as  well  as  the  standardised  instructions  contained 
therein. 

 

FCC Statement 

This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the 

following two conditions: 

1. This device may not cause harmful interference, and 
2. This device must accept any interference received, including interference that may 

cause undesired 

operation. 
 

NOTE

 

Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 

compliance could void the user’s authority to operate the equipment. 

 

Federal Communication Commission (FCC) Statement 

Industry Canada (IC) Statement 
 

This  device  contains  licence-exempt  transmitter(s)/receiver(s)  that  comply  with 

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).  

Operation is subject to the following two conditions: 
1 . This device may not cause interference. 
2. This device must accept any interference, including interference that may cause 

undesired operation of the device. 

 

Summary of Contents for Easy Access Transponder Stand-Alone





























Reviews: