background image

Universal automatic switch 180° 2.20 m 

Light Management  

Universal automatic switch 180° 2.20 m 

Art.-No.: AS..1280-1..

Operating instructions 

1 Safety instructions 

Electrical equipment may only be installed and fitted by electrically skilled persons. 

Failure to observe the instructions may cause damage to the device and result in fire and 
other hazards. 

Danger of electric shock. Always disconnect before carrying out work on the devise or 
load. At the same time, take into account all circuit breakers that supply dangerous 
voltage to the device or load. 

Danger of electric shock. Device is not suitable for disconnection from supply voltage. 
The load is not electrically isolated from the mains even when the device is switched off. 

Do not press on the sensor window. Device can be damaged. 

Disconnect before mounting the cover, malfunction possible. 

Keep button cells out of reach of children! If button cells are swallowed, get medical help 
immediately. 

Risk of explosion! Do not throw batteries into fire. 

Risk of explosion! Do not recharge batteries. 

The device is not suitable for use as a burglar alarm or other alarm. 

These instructions are an integral part of the product, and must remain with the end 
customer. 

2 Device components 

Figure 1 

(1)  Insert 
(2)  Frame 
(3)  Motion detector 
(4)  LED red 
(5)  Button Off/Auto 
(6)  LED yellow 

1/13 

32576803 
J:0082576803 

03.05.2011 

Summary of Contents for AS 1280-1 Series














Reviews: