Julabo CORIO CP-1000F Original Operating Manual Download Page 38 | Manualshive

Page: 38 / 72

background image

Initial operation

38

7.2.2 Connect refrigerated circulator

This section describes how the circulator is connected as a refrigerated
circulator.



The circulator is mounted on a refrigeration unit.



The connection cable, mains cable and CAN bus cable are ready for use.

1. Connect the connection cable [1] of the circulator with the refrigeration

unit.

2. Connect the CAN plugs of both units with the CAN bus cable [2].
3. Connect the refrigeration unit to mains power [3] using the power cable.



The refrigerated circulator is connected. Alternatively, the units can be

connected to separate circuits. If necessary, the power supply must be set
up in the unit setting.

«
...
36
37
38
39
40
...
»

Summary of Contents for CORIO CP-1000F









































































Reviews:

No comments

Related manuals for CORIO CP-1000F

Brand: Ebac Pages: 8

Brand: Casablanca Pages: 14

Brand: Casablanca Pages: 2

Brand: Gaggenau Pages: 68

Brand: Flexit Pages: 44

Brand: Greenheck Pages: 1

Brand: ZALMAN Pages: 11

Brand: ebm-papst Pages: 11

Pelham HVFC# 2299

Brand: hudson valley Pages: 12

Brand: ebm-papst Pages: 5

Brand: Qlima Pages: 20

Brand: Air Specialties Express Pages: 4

Brand: ebm-papst Pages: 9

Brand: ebm-papst Pages: 11

Brand: ebm-papst Pages: 12

Brand: Aprilaire Pages: 12

Brand: oneConcept Pages: 32

ELEGANCE EL1003DT

Brand: Vectaire Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands