manualshive.com logo in svg

JUKI J-350QVP, Instruction Manual, Page: 17 / 32

Share
Download
JUKI J-350QVP Instruction Manual Download Page 17

– 16 –

Adjusting the thread guide base

Thicker toward downside

Loosen the screw of the thread 
guide base to make adjust-
ment.

Loosens

Tightens

Move up

Thicker toward upside

Move down

Good

Thread unevenly wound around the bobbin would badly affect the bobbin thread tension.

Checking the needle

Attaching the needle

Check the needle for its straightness occasionally. Any defective needle 
would cause needle breakage, stitch skipping, thread breakage or 
damage to materials.

Parallel

Flat plate

Tightens

 Loosens

Needle clamp screw

Needle with 

a round shank

Scarf

Due to the position of the machine in both the frame and sit 

down table, the scarf goes to the back and the groove to the 

front.

Attaching the needle

1. Turn OFF the power switch.
2. Lower the presser foot.
3. Move the needle bar up to the highest position of its 

stroke.

4. Holding a needle with its long groove faced to the 

left, insert the needle into the needle bar until it will 
go no further. Then, tighten the needle clamp screw.

   CAUTION

Turn OFF the power switch.

Summary of Contents for J-350QVP

































Reviews:

No comments