manualshive.com logo in svg

JUKI IT-10, Instruction Manual

Share
Download
JUKI IT-10 Instruction Manual Download Page 33

– 31 –

  13. ERROR INdICATION

Error code

Error description

Restoration method

E011

External medium not inserted

No medium is inserted.

Reset (Press the 

 switch.)

E012

Read error

Data cannot be read from the medium.

Reset (Press the 

 switch.)

E013

Write error

Data cannot be written into the medium.

Reset (Press the 

 switch.)

E015

Format error

The medium cannot be formatted.

Reset (Press the 

 switch.)

E016

External medium capacity exceeded

The capacity of the medium is insufficient.

Reset (Press the 

 switch.)

E021

Medium access failure

Reset (Press the 

 switch.)

E065

Network transmission failure

Data cannot be transmitted to the network.

Reset (Press the 

 switch.)

E067

ID data reading failure

ID data stored in the medium is corrupt.

Reset (Press the 

 switch.)

E204

USB insertion

The sewing machine was started up with USB inserted.

Reset (Press the 

 switch.)

E205

Remaining ISS buffer capacity warning

The buffer for ISS data storage is going to be full soon. When it is 
full and used, data will be erased from the oldest ones.

Reset (Press the 

 switch.)

E703

Panel connection to an unexpected sewing machine (model 
error)

When the models of panel and sewing machine do not match in 
initial communication.

Connect the operation panel to 
the correct sewing machine.

E704

Unmatched system version

System version does not match in initial communication.

Re-write the program.

E915

Operation panel 

⇔

 electrical BOX communication error

Error occurred in data communication.

Turn OFF the power

E938

Error in program rewriting file

Turn OFF the power

E949

No file for program rewriting

Turn OFF the power

E950

There are several files for program rewriting

Turn OFF the power

This system enables interlock (or restriction of functions) to prevent the problem from spreading in case a prob-
lem is detected, and contains the following error codes to notify the problems. When requesting for service, 
please also check the error code.Refer to the Instruction Manual for the control box errors on the control box. 

Error code display

Summary of Contents for IT-10


































Reviews:

No comments

Brands by name

Popular brands

Load more brands