JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download

Page: 79 / 163

– 74 –

3) Changing over the steps

A step in the pattern that is currently selected with PATTEN SE-
LECTION button

is changed over to the

previous step or the subsequent step in that pattern.

①

Changing over the pattern

When STEP CHANGEOVER (BEFORE) button

is pressed on the step edit screen, the sewing order of the
currently-selected pattern and its previous pattern is changed
over.

When STEP CHANGEOVER (AFTER) button

pressed, the sewing order of the currently-selected pattern
and its subsequent pattern is changed over.

4) Deleting a step

The pattern that is currently selected with PATTEN SELECTION
button is deleted.

①

Deleting a pattern

When STEP DELETE button

is pressed on the step

edit screen, the currently-selected pattern is deleted from the
registered cycle step.

2) Inserting a step

A step is inserted into the position immediately before the pat-
tern that is currently selected with PATTEN SELECTION button

①

Selecting a pattern into which a step is inserted

When STEP INSETION button

is pressed on the step

edit screen, the pattern selection screen is displayed.

②

Inserting a step

Select the pattern into which you want to insert a step, and
press ENTER button

. Then, the step is inserted imme-

diately before the currently-selected pattern, and the screen
returns to the step edit screen.

F
G

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Search results

Summary of Contents for AMS-221F3020RSW/AW-3

Reviews:

Related manuals for AMS-221F3020RSW/AW-3

Brands by name

Popular brands