manualshive.com logo in svg

JUKI AMS-221F3020RSW/AW-3, Instruction Manual

Share
Download
JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download Page 147

– 142 –

1-9-2. Points to be applied with JUKI Grease A

Use grease tube A (part number: 40006323) supplied with the unit for adding grease to 

any points other than the points specified below. If any grease other than the specified 

one is used, the related components can be damaged.

1-9-1. Location where exclusive grease is provided

JUKI Grease A 

❶

, exclusive joint for JUKI Grease, setscrew and exclusive grease for linear guide 

❷

 

are supplied in the accessory box. Add grease periodically (when the grease runout warning No. E220 
is displayed on the panel or once a year) to points to be applied with grease. If grease has decreased 
due to cleaning of the sewing machine or any other reasons, be sure to immediately add grease.

Spare parts No.

JUKI Grease A

10g tube

40006323

100g tube

23640204

Grease specifically developed 

for the linear guide 

70g tube

40097886

When the grease runs short, be sure to purchase new grease.

JUKI Grease A

❶

Do not use Grease A and Grease B with mixed. Be sure to use the specified grease 

without fail. JUKI Grease A 

❶

 and exclusive grease for linear guide 

❷

 are supplied in the 

accessory box. 

   ■  Adding grease to the needle bar upper and lower bushings section, slide block section 

and intermediate presser bar lower bushing section

1)  Open the frame cover to remove intermediate 

presser auxiliary spring B

❶

.

2)  Apply JUKI Grease A onto periphery of nee-

dle bar 

❷

. Turn the sewing machine by hand 

to apply grease onto the entire periphery of 
the needle bar. Turn needle bar upper bush-
ing grease cover.

 

Fill the grease through the grease inlet of the 
needle bar upper bushing.

 

Remove setscrew 

❹

 of the needle bar lower 

bushing grease inlet. Put JUKI GREASE A 
into hole 

❺

. Tighten setscrew 

❹

. Fill inside 

of the bushing with JUKI GREASE A.

❶

❽

❾

❺

❹

Grease 

❷

 specifically 

developed for the 

linear guide 

WARNING :

  Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of 

the sewing machine. In addition, attach the covers which have been removed before operation back 

in place.

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands