manualshive.com logo in svg

JUKI AMS-221F3020RSW/AW-3, Instruction Manual, Page: 108 / 163

Share
Download
JUKI AMS-221F3020RSW/AW-3 Instruction Manual Download Page 108

– 103 –

2-9-2. AW number of stitches input mode, AW operation mode and setting of the 

allowance length of the remaining length

When you press 

 

A

 on the AW operation screen, the AW set-

ting item list screen is displayed.

On the AW setting item list screen, the below-listed data items can 
be set by pressing the buttons corresponding to the respective data 
items.

Ⓐ

  :  Selection of the bobbin changing method

Ⓑ

  :  Setting of the thread winding length

Ⓒ

  :  Setting of the allowance length of the remaining thread

Ⓓ

  :  Setting of the thread raveling strength

Ⓔ

  :  Adjustment of the bobbin thread end length

Ⓕ

  :  Percentage of allowance of thread consumption 

Detailed explanation will be given from the next page.

< AW setting item list screen >

A

Ⓐ
Ⓑ
Ⓒ

Ⓓ
Ⓔ

Ⓕ

< AW operation screen >

Summary of Contents for AMS-221F3020RSW/AW-3




































































































































































Reviews:

No comments