JUKI AMS-210E-1306 Instruction Manual Download

Page: 82 / 128

– 78 –

“Ready” key

This key changes over the setting state from
the panel to the sewing state where the

sewing machine actually operates.

Sewing LED

This LED goes off at the time of setting state and
lights up at the time of sewing state. Changeover

can be performed with “Ready” key.

“Reset” key

This key is used for canceling error or
returning the set value to the initial value.

“Mode” key

This key makes the setting mode of the
memory switch.

“+ / Feed forward” key and “– / Feed

backward” key

This key is used for changing pattern No. and
X/Y scale, and feed forward/feed backward.

“Selection” key

This key selects the item to be set. Item
selection LED of the selected item and the

set value are displayed.

Data indication LED

This LED indicates the set values of the
selected items such as pattern No., X/Y

scale, etc.

Item selection LED

LEDs of the selected items light up.

Needle thread clamp ON/OFF key

This key selects effective/ineffective of needle
thread clamp. When it is effective, needle

thread clamp display LED lights up.

Needle thread clamp display LED

When this LED lights up, needle thread clamp
operates.

Needle thread clamp display LED

This key registers the pattern. When this key
is pressed, the pattern registered here can
sew immediately.

X/Y scale, sewing position, etc. can be
changed and registered.

Pattern No.

X scale

Y scale

Max. speed

limitation

Sewing

counter

Bobbin

winder

Intermediate

presser

height

Thread

tension

3. WHEN USING CP-20

3-1. Name of each section of CP-20

Summary of Contents for AMS-210E-1306

































































































































Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands

JUKI AMS-210E-1306, Instruction Manual

Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands