JUKI AMS-210E-1306 Instruction Manual Download

Page: 30 / 128

– 26 –

2-2. Buttons to be used in common

The buttons which perform common operations in each screen of IP-400 are as follows :

CANCEL button

→

This button closes the pop-up screen.

In case of the data change screen, the data being

changed can be cancelled.

ENTER button

→

This button determines the changed data.

UP SCROLL button

→

This button scrolls the button or the display in the

upward direction.

DOWN SCROLL button

→

This button scrolls the button or the display in the

downward direction.

RESET button

→

This button performs the release of error.

NUMERAL INPUT button

→

This button displays ten keys and input of numerals

can be performed.

CHARACTER INPUT button

→

This button displays the character input screen.

→

Refer to

“

-2-14. Naming users' pattern”

RESSER LOWERING button

→

Presser is lowered, and the presser lowering screen
is displayed. To lift presser, press presser lift button
displayed in the presser lowering screen.

Bobbin winder button

→

Bobbin thread winding is performed.

→

Refer to

“

-2-11. Winding bobbin thread”

Summary of Contents for AMS-210E-1306

































































































































Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands

JUKI AMS-210E-1306, Instruction Manual

Search results

Summary of Contents for AMS-210E-1306

Reviews:

Related manuals for AMS-210E-1306

Brands by name

Popular brands