background image

– 18 –

4-7. Intermediate presser height

0.5 mm

1) Select the intermediate presser with 

 key.

2)  Press 

 key to lower the intermediate 

presser.

3)  Adjust with 

 or 

 key so that the 

clearance between the bottom end of 
intermediate presser and the cloth is 0.5 mm 
(thickness of thread used) when the needle is in 
its lowest position. 

h

[IP-400]

A

B

[CP-20]

  Press INTERMEDIATE PRESSER SETTING button 

A

 and adjust 

with TEN keys 

B

 so that the clearance between the bottom end of 

intermediate presser and the cloth is 0.5 mm (thickness of thread 

used). 

 

1.  Setting range of the intermediate presser is up to the standard of 3.5 mm.

 

  However, when using DP X 17 needle for H type or the like, the setting range can 

be changed up to max. 7 mm with memory switch U112.

 

2.  When increasing the height of intermediate presser or making the needle size 

thicker, confirm the clearance between the wiper and the components. Wiper 
cannot be used unless the clearance is secured. In this case, turn OFF the wiper 
switch, or change the set value of memory switch U115.

When raising the intermediate presser height, turn the pulley by hand to lower the 

needle bar, and confirm that the needle bar does not interfere with the intermediate 

presser. (When using DP X 5 needle, use the sewing machine with the height of 3.5 

mm or less.)

Summary of Contents for AMS-210E-1306

































































































































Reviews: