JUKI AMS-210E-1306 Instruction Manual Download Page 18

Page: 18 / 128

– 14 –

3-16. Installing the eye protection cover

WARNING :

Be sure to attach this cover to protect the eyes from the disperse of needle breakage.

Use eye protection cover

after securely

attaching it on face plate cover

with screw

4. PREPARATION OF THE SEWING MACHINE

4-1. Lubrication

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of

the sewing machine.

Check that the place between lower line

and

upper line

is ﬁlled with oil. Fill there with oil using

the oiler supplied with the machine as accessories
when oil is short.

The oil tank which is ﬁlled with

oil is only for lubricating to the

hook portion. It is possible to

reduce the oil amount when the

number of rotation used is low

and the oil amount in the hook

portion is excessive. (Refer to

“

-1-9. Amount of oil supplied

to the hook”

1. Do not lubricate to the places other than the oil tank and the hook of Caution 2

below. Trouble of components will be caused.

2. When using the sewing machine for the first time or after an extended period

of disuse, use the machine after lubricating a small amount of oil to the hook
portion. (Refer to

“

-1-2. Adjusting the needle-to-shuttle relation”

. )

Summary of Contents for AMS-210E-1306

































































































































Search results

Summary of Contents for AMS-210E-1306

Reviews:

Brands by name

Popular brands

JUKI AMS-210E-1306, Instruction Manual

Search results

Summary of Contents for AMS-210E-1306

Reviews:

Brands by name

Popular brands