manualshive.com logo in svg

Judo JRSF Series, Installation And Operating Instructions Manual, Page: 47 / 55

Share
Download
Judo JRSF Series Installation And Operating Instructions Manual Download Page 47

 

 

 

 

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)                                                                                                                                                                           

 

All rights reserved. 

JUDO Wasseraufbereitung GmbH 

© JUDO Wasseraufbereitung GmbH 

Postfach 380 

 D-71351 Winnenden 

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special 
approval. 

Tel. +49 (0)7195-692-0 

 Fax +49 (0)7195-692-188 

Revision level: 24.05.2017 

E-mail: [email protected] 

 judo.eu 

47  

 

 

7.1.3 

Manual setting of the Hall pulses with automatic balancing 

 

  Switch off the control unit, then remove the cover of the terminal compartment. 

 

 

Attention 

The DIP switches must only be switched in a zero-volts state! 

 

 

Set DIP switches 1 + 6 to ON, then switch the control unit back on. “Reading in Hall values” with 
filter-specific maximum and minimum values is output to the display. 

  Move the linear drive with key 

 or 

 until the maximum and minimum values no longer change. 

Manual setting is ended. 

  Switch on the control unit and set DIP switches 1 + 6 back to OFF. 

  Switch the control unit back on by pressing the key 

 (5 seconds). 

 

 

If the control unit again indicates “Hall fault”, repeat the process or request the 
assistance of JUDO customer service! 

 

  Switch off the control unit and disconnect the linear drive from the control unit. 

  Reinstall the linear drive correctly in the motor mounting. 

  Correctly reattach the cover of the terminal compartment on the control unit. 

  Reconnect the linear drive with the control unit, switch on and, if necessary, reprogram according to 

the local requirements (see Chap. 5.4 - 5.5). 

 

7.2 

Replacing the solenoid valve 

 

  Switch off the control unit and unscrew the device plug of the solenoid valve. 

  Stop the control medium supply, then remove the control medium connection at the solenoid valve. 

  Remove the solenoid valve from the shut-off valve pneumatic drive. 

  If necessary seal connection A of the new solenoid valve (see Chap. 3.5.3) using PTFE tape and 

install it preferably with the drive up on the diaphragm valve. 

  Re-attach the control medium connection and the pressure relief line to the solenoid valve, then 

release the control medium again. 

  Correctly refit the device plug again at the solenoid valve and switch the control unit on again. 

 

 

Summary of Contents for JRSF Series
























































Reviews:

No comments