manualshive.com logo in svg

Judo JRSF Series, Installation And Operating Instructions Manual, Page: 38 / 55

Share
Download
Judo JRSF Series Installation And Operating Instructions Manual Download Page 38

 

 

 

 

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)                                                                                                                                                                           

 

All rights reserved. 

JUDO Wasseraufbereitung GmbH 

© JUDO Wasseraufbereitung GmbH 

Postfach 380 

 D-71351 Winnenden 

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special 
approval. 

Tel. +49 (0)7195-692-0 

 Fax +49 (0)7195-692-188 

Revision level: 24.05.2017 

E-mail: [email protected] 

 judo.eu 

38  

 

 

6.1.1 

General procedure 

 

 

Attention 

To prevent possible damage to the JUDO JRSF automatic backwashing protection filter 
and its piping system, before first operation under full load, the closing speed of the 
shut-off valve (see Chap. 6.1.3) and the stroke limiter of the pneumatic drive (see Chap. 
6.1.2) must be set to match the local circumstances! 

 

  The closing speed of the pneumatic drive must be regulated via the exhaust throttle of the solenoid 

valve (see Chap. 6.1.3). 

  Adjust the stroke limiter at the shut-off valve pneumatic drive (see Chap. 6.1.2) 

  Carefully open the site shut-off valves upstream and downstream of the JUDO JRSF automatic 

backwashing protection filter. 

  If necessary bleed the control line of the differential pressure gauge at the connection (-) via the 

mini-ball-valve, then carefully reattach the control line. 

  Carefully open both mini-ball valves of the differential pressure gauge. 

  Set switching point S1 at the differential pressure gauge (max. 0.5 bar). 

  Switch on the control unit and program in consideration of the local requirements. 

  As a function check initiate a manual backwash. 

6.1.2 

Adjust the stroke limiter at the shut-off valve pneumatic drive 

 

 

Attention 

Only perform setting of the stroke limiter if the system is completely depressurised!

 

 

 

Fig. 17: Setting of the stroke limiter 
 

1  Position indicator 

3  Counter nut (13 mm AF) 

2  Stroke limiter adjustment screw (5 mm AF) 

   

1 

3 

2 

3 

2 

Summary of Contents for JRSF Series
























































Reviews:

No comments