SAFETY AND PROPER USAGE
To ensure safe and enduring performance of this product, you must comply strictly with the instructions enclosed herein.
Non-compliance with instructions or improper handling of the product will void your warranty! Usage of this product in
conditions not specified in this manual or in contrary to the instructions hereby provided is considered IMPROPER. The
manufacturer will not be held liable for any damages resulting from improper use of the product.
SAFETY & WARNING INSTRUCTIONS
- Observe valid and generally accepted safety rules when planning, installing and using this product.
- Take proper measures to prevent unintentional operation of the product or damage to it.
- Do not attempt to disassemble this product or lines in the system while they are under pressure.
- Always depressurize the compressed air system before working on the system.
It is important that personnel use safe working practices and observe all regulations and legal requirements for safety
when operating this product. When handling, operating or carrying out maintenance on this product, personnel must
employ safe engineering practices and observe all local health & safety requirements & regulations. International users
refer to regulations that prevail within the country of installation. Most accidents, which occur during the operation and
maintenance of machinery, are the result of failure to observe basic safety rules or precautions. An accident can often be
avoided by recognizing a situation that is potentially dangerous. Improper operation or maintenance of this product could
be dangerous and result in an accident causing injury or death. The manufacturer cannot anticipate every possible
circumstance, which may represent a potential hazard. The WARNINGS in this manual cover the most common potential
hazards and are therefore not all-inclusive. If the user employs an operating procedure, an item of equipment or a method
of working which is not specifically recommended by the manufacturer he must ensure that the product will not be
damaged or made unsafe and that there is no risk to persons or property.
NEVER CHANGE ORIGINAL COMPONENTS WITH ALTERNATIVES
WARNING
This product can expose you to chemicals
including lead, which is known to the State of California to cause
cancer and/or birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov
9602
INSTALLATION INSTRUCTIONS
Before installing this product, make sure it complies with your request and that it suits
your application!
1.1 Unpack the unit and visually inspect for any transport damage incurred after leaving our factory.
1.2 Depressurise the system before installation or maintenance is carried out!
1.3 Locate a suitable point in your compressor room to place your Condensate Cleaner. This point
must be near a suitable sewage point. The unit is designed to easily fit against a wall or structure.
1.4 Screw the inlet nipple with rubber O-ring in to its marked location using a 22mm wrench.
Do not over tighten!
1.5 Mount the Mounting bracket (back) against a wall or other suitable structure. Make sure the bracket
is level.
1.6 After placing the Mounting bracket (back) you can place the front bracket and screws, using a 5mm
wrench. Do not tighten the screws. Make sure the front part of the bracket can be adjusted to fit the
Condensate Cleaner.
1.7 Place the Condensate Cleaner and fix the bracket by tightening the screws.
1.8 Connect the condensate collection pipe to the inlet.
1.9 Connect the outlet from the Condensate Cleaner to a suitable sewage point.
Make sure the condensate always flows down!
1.10 Fill the Condensate Cleaner with water until it is filled and water flows out of the outlet point.
1.11 Your Condensate Cleaner is ready for operation!
0
°
TECHNICAL SPECIFICATIONS
Max. oil adsorption element’s
0,5 gallon
Inlet connection
1/2” BSP
Outlet connection
1/2” BSP
Test drain
Yes
Housing material
ABS
Housing colour
Black
Lid colour
Grey
Mineral lubricants
Yes
Synthetic lubricants
Yes
Stabile condensate emulsions
Yes
Poly Glycol
Yes, consult factory
Max. compressor capacity
70 CFM
DIMENSIONS (inches)
EXPLODED VIEW
REPLACEMENT PARTS
Description
Part No.
SEPREMIUM 70
(Optionally without bracket)
9602
SEPREMIUM 70
PSI
Inlet nipple
Housing
Test drain
Mounting bracket front
Test bottle
Private label area
Outlet nipple
Mounting bracket back
Washer (2*)
Bolt (2*)
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
