JOHNSON SYSTEMS CS-DMX Series User Manual Download Page 4 | Manualshive

Page: 4 / 12

background image

www.johnsonsystems.com

4

6-Position Connector (J1) For:

• Power Supply Input (COM, V+)

• Button Contacts (ON, DIM, RST)

• Master Pot (MP) Analog Output
DMX Output Range Calibration Jumper (JP1)
Security Enable/Disable Jumper (JP2)
Factory Only Jumper(s)

DMX Input Connector (J1)
DMX Output Connector (J2)
DMX Termination Jumper (JP1)

"ON", "DIM", and "OFF" Buttons With Integral LED's
Master (M) Slider
Infared LED Sensor
Secondary (3, 6, 9, or 12) Sliders

CS-DMX Series Control Station Diagrams

«
...
2
3
4
5
6
...
»

Summary of Contents for CS-DMX Series













Reviews:

No comments

Related manuals for CS-DMX Series

Brand: Lakeland Pages: 12

Brand: Pacer Pages: 20

Brand: Farm Aid Pages: 21

Brand: Yamaha Pages: 58

Brand: Breville Pages: 20

Brand: Oster Pages: 8

AWCL-300-6P-Audio-DMX

Brand: Alphawave Pages: 12

Brand: A SYSTEMS Pages: 16

Brand: Carlisle Pages: 12

Brand: The t.mix Pages: 18

Brand: The t.mix Pages: 24

Brand: Gemini Pages: 4

Pro RDP-SHM20 SOLO

Brand: Raider Pages: 78

Brand: Ecler Pages: 38

Brand: Dateq Pages: 11

Brand: Applica Pages: 2

Brand: Univex Pages: 2

Brand: YORKVILLE Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands