Johnson Matthey Tracerco PED Blue User Manual Download Page 18 | Manualshive

Page: 18 / 25

Johnson Matthey Tracerco PED Blue User Manual Download Page 18

MN1010 Rev. G

18 of 25

3.7

Using a PED+ or PED-ER+ in the handheld mode

Personal dose is not accumulated in handheld mode

In the handheld mode, the PED+ and PED-ER+ measures the dose rate which is compensated for
the fact that it is no longer being worn on the body. Therefore, the PED+ should be held away from
the body whenever possible.

Use a PED+ or PED-ER+ in the handheld mode as follows:

1. On the

Main

menu

> Handheld mode

.

Attention

: If the menu item is not available, enable the feature in

DoseVision™.

2. Hold the PED so that the GM tube window is facing forwards or in the direction of the area being measured.

3. View the readings screen that shows the following:

Handheld mode icon

Indicates that PED is in the handheld mode.

Peak dose rate

Peak dose rate experienced since the PED was last reset using

DoseVision™.

Dose rate bar graph

Bar graph representing the current dose rate.

Dose rate reading

Current dose rate measurement. The measurement is compensated for the device being worn away
from the upper body. The value is filtered to provide a stable reading.

Activity graph

Activity graph to help detect quick changes in radiation fields. The activity graph shows a rolling 30
second chart of the activity. Each bar represents the number of counts detected within the last second.

«
...
16
17
18
19
20
...
»

Summary of Contents for Tracerco PED Blue


























Reviews:

No comments