manualshive.com logo in svg

Johnson Controls VFD66JCB-1, Installation Manual

Share
Download
Johnson Controls VFD66JCB-1 Installation Manual Download Page 20

20

Installation Guide

www.johnsoncontrols.com

Issue Number:  2

6

Technical specifications

Building Efficiency

507 East Michigan Street
Milwaukee
WI 53202

Model

VFD66

Drive voltage rating

230Vac, 460Vac @ 60Hz (230Vac, 400Vac @ 50Hz)

Output Voltage/Output frequency 230Vac, 460Vac @ 60Hz 
Switching frequency

3kHz

Duty

Normal

Overload limit

110% overload current for 60s

Acceleration/Deceleration

5 s/100Hz

Start/Stop

Terminal control

Motor cable lengths

≤

50m

Ambient temperature

-40

°

C to 50

°

C (-40

°

F to 122

°

F)

Storage temperature

-40

°

C to 50

°

C (-40

°

F to 122

°

F)

Altitude

Rated altitude: 1000m (3300 ft)
Reduce the normal full load current by 1% for every 100m (330ft) above 
1000m (3300ft) up to a maximum of 3000m (9842ft)

Humidity

Maximum relative humidity 90% non-condensing at 40

°

C (104

°

F)

Storage humidity

Maximum relative humidity 93%, 40

°

C, 4 days

Vibration

Meets EN61800-5-1 and ETS300019-2-2

Enclosure

IP00 (UL Open Type)

Approvals

RoHS compliant, CE Approval, UL/cUL Approval (JCI file number E244421), 
C tick approval

Dimensions

See Figure 3-1 on page 9

Weight

2.2 lb (1kg)

The performance specifications are nominal and conform to acceptable industry 
standards. For application at conditions beyond these specifications, consult Johnson 
Controls/PENN Refrigeration Application Engineering at 1-800-275-5676. Johnson 
Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of 
its products. 

NOTE

Summary of Contents for VFD66JCB-1























Reviews:

No comments

Brands by name

Popular brands

Load more brands