background image

TEC20x6(H)-4 and TEC20x6H-4+PIR Series Wireless Thermostat Controllers with Dehumidification 
Capability, Fan Control, and Occupancy Sensing Capability 

24

Technical Specifications

Table 8:  Accessories (Order Separately)

Code Number

Description

SEN-600-1

Remote Indoor Air Temperature Sensor

SEN-600-4

Remote Indoor Air Temperature Sensor with Occupancy Override and LED

TE-6361M-1

1

Duct Mount Air Temperature Sensor

TE-636S-1

Strap-Mount Temperature Sensor

TEC20-A-1

Replacement Antenna for TEC20 Coordinator

TEC20-RA-1

2

Remote Antenna for TEC20 Coordinator

NPB-PWR

3

DIN Rail Mount 24 VAC/DC Power Module for TEC20 Coordinator

TEC20-8X-1

120 VAC to 15 VDC Power Supply for TEC20 Coordinator

TEC20-9B-1

Replacement Battery Pack for TEC20 Coordinator

TEC-6-PIR

4

Cover with Occupancy Sensor

TEC-6H-PIR

5

Cover with Occupancy Sensor for Hospitality Models

1.

Additional TE-636xx-x Series 10k ohm Johnson Controls Type II Thermistor Sensors are available; refer to the 

TE-6300 Series Temperature Sensors Product Bulletin (LIT-216320)

 for more details.

2.

This antenna is used when the TEC Coordinator is installed inside a metal cabinet, or when a remote antenna is required by 
physical installation.

3.

DIN Rail: Type NS35/7.5 (35 x 7.5 mm) and DIN rail end clips. Length of DIN rail depends on the number of DIN rail 
mounted options.

4.

The TEC-6-PIR Accessory Cover can be used to replace the existing cover on a non-PIR TEC20x6-4 Series Thermostat 
Controller to provide occupancy sensing capability.

5.

TEC-6H-PIR Accessory Cover can be used to replace the existing cover on a non-PIR TEC20x6H-4 Series Thermostat 
Controller to provide occupancy sensing capability.

TEC20x6(H)-4 and TEC20x6H-4+PIR Series Wireless Thermostat Controllers with 
Dehumidification Capability, Fan Control, and Occupancy Sensing Capability (Part 1 of 2)

Power Requirements

19 to 30 VAC, 50/60 Hz, 2 VA (Terminals 4 and 5) at 24 VAC Nominal, Class 2 or 
Safety Extra-Low Voltage (SELV)

Relay/Triac Contact Rating

On/Off and Floating Control:

 19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum,

3.0 A In-Rush, Class 2 or SELV

Analog Output Rating 

Proportional Control:

 0 to 10 VDC into 2k ohm Resistance (Minimum)

Fan Relay Output Rating

19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush, Class 2 or SELV

Auxiliary Output Rating

Triac Output:

 19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush

Binary Inputs

Voltage-Free Contacts across Terminal Scom to Terminals BI1, BI2, or UI3

Analog Inputs

Resistive Inputs (RS and UI3) for 10k ohm Johnson Controls Type II Negative 
Temperature Coefficient (NTC) Thermistor Sensors

Wire Size

18 AWG Maximum, 22 AWG Recommended

Recommended Transmission 
Range

Through Walls: 

10 m (30 ft)

Line-of-Sight (Open Space): 

30 m (100 ft)

RF Band

Direct-Sequence Spread-Spectrum Transmission; 2.4 Ghz unlicensed band

Transmission Power

10 mW Maximum

Temperature Range

Backlit Display:

 -40.0°C/-40.0°F to 50.0°C/122.0°F in 0.5° increments

Heating Control:

 4.5°C/40.0°F to 32.0°C/90.0°F in 0.5° Increments

Cooling Control: 

12.0°C/54.0°F to 38.0°C/100.0°F in 0.5° Increments

Temperature Sensor Type 

Local 10k ohm Negative Temperature Coefficient (NTC) Thermistor

Resolution 

±0.1C°/±0.2F°

Summary of Contents for TEC20x6-4 Series


























Reviews: