background image

TEC2001-4 and TEC2001-4+PIR Single-Stage Wireless Thermostat Controllers Installation Instructions

9

DI2

Configuration of Digital Input 2.
Default: 

None

(None):

 No function is associated with an input.

(RemNSB):

 Remote Night Setback (NSB) via a time clock input, an 

occupancy sensor, or from a voltage-free contact. 
Contact open = Occupied; contact closed = Unoccupied.

(RemOVR):

 Temporary occupancy request via a remote input. This 

override function is controlled by a manual remote occupancy 
override. When enabled, this condition disables the override 
capability of the thermostat controller.

(Filter):

 A Filter alarm is displayed. This alarm can be connected to 

a differential pressure switch that monitors a filter.

(Service): 

A Service alarm is displayed on the thermostat controller 

when the input is energized. Tie this input into the air conditioning 
unit control card, which provides an alarm if a malfunction occurs.

(Fan lock):

 A backlit flashing Fan lock alarm is displayed on the 

thermostat controller when the input is not energized. This alarm is 
used in conjunction with a local airflow sensor connected to the 
input. The thermostat controller heating or cooling action is locked 
out if no airflow is detected 10 seconds after the fan (Terminal G) is 
energized. Contact open = no airflow; contact closed = airflow 
present.

MenuScro

Gives the option of having the 
display continuously scroll the 
parameters.
Default: 

on

(off):

 The scroll is inactive.

(on):

 The scroll is active.

Lockout

Selectable Lockout Levels for 
limiting end user keypad interaction.
Default: 

0

Function

Level

(0)

(1)

(2)

Resume/Override 
Scheduling

Access

Access

No Access

Permanent 
Temperature 
Setpoints

Access

No Access

No Access

Temporary 
Temperature 
Setpoints

Access

Access

No Access

System Mode Setting

Access

No Access

No Access

Fan Mode Setting

Access

No Access

No Access

Pwr del

1

Sets the delay time period at 
thermostat controller powerup, or at 
each time power is removed and 
reapplied, before any operation 
(fan, heating, or cooling) is 
authorized. Also can be used to 
sequence the startup of multiple 
units in one location.
Default: 

10.0 sec

Range: 

10.0

 to 

120.0 sec

Frost pr

Provides a minimum heating 
setpoint of 5.5°C/42.0°F to prevent 
freezing in the zone controlled by 
the thermostat controller.
Default: 

off

(on):

 Enabled

(off):

 Disabled

Heat max

2

Sets the Occupied and Unoccupied 
maximum Heating setpoint values.
Default: 

32.0°C/90.0°F

Range: 

4.5°C/40.0°F 

to 

32.0°C/90.0°F

Table 3:  Installer Configuration Menu  (Part 2 of 5)

Parameter 
Appearing 
on Display

Description and Default

Selection Options

Summary of Contents for TEC2001-4

















Reviews: