background image

Published in U.S.A.

www.johnsoncontrols.com

TEC2001-4 and TEC2001-4+PIR Single-Stage Wireless Thermostat Controllers Installation Instructions

16

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners. © 2010 Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI  53202

Compliance

United States:

UL Listed, File E27734, CCN XAPX, 
Under UL 873, Temperature Indicating and Regulating Equipment
FCC Compliant to Part 15.247 Regulations for Low Power Unlicensed Transmitters

Canada:

UL Listed, File E27734, CCN XAPX7, 
Under CSA C22.2 No. 24, Temperature Indicating and Regulating Equipment
Industry Canada, ICES-003

Shipping Weight

TEC2001-4 Model:

 0.75 lb (0.34 kg)

TEC2001-4+PIR Model:

 0.77 lb (0.35 kg)

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these 
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or 
misuse of its products.

TEC2001-4 and TEC2001-4+PIR Single-Stage Wireless Thermostat Controllers (Part 2 of 2)

Summary of Contents for TEC2001-4

















Reviews: