Johnson Controls IOM3733 Installation Instructions Manual Download Page 12

Table 7: Status LEDs and description of LED states

LED label

LED color Normal LED

state

Description of LED states

POWER

Green

On Steady

Off Steady = No Supply Power. The expansion module’s

polyswitch/resettable fuse may be open. Check output wiring for

short circuits and cycle power to expansion module.

On Steady = Power Connected

FAULT

Red

Off Steady

Off Steady = No Faults

On Steady = Device Fault

Blink - 2 Hz = Download or Startup in progress: not ready for

normal operation

SA/FC BUS

Green

Blink - 2 Hz

Blink - 2 Hz = Data Transmission (normal communication)

Off Steady = No Data Transmission (N/A - auto baud not

supported)

On Steady = Communication lost; waiting to join communication

ring

EOL

Amber

Off (Except on

terminating

devices)

On Steady = EOL switch in ON position

Off Steady = EOL switch in Off position

Repair information

If a controller fails to operate within its

specifications, replace the controller. For a

replacement controller, contact your Johnson

Controls representative.

Accessories

Table 8: Accessories Ordering Information

Product Code Number Description

Mobile Access Portal

(MAP) Gateway

Refer to the 

Mobile Access Portal Gateway Catalog Page (LIT-1900869)

 to identify the

appropriate product for your region.

Note: 

The MAP Gateway serves as a replacement for the BTCVT, which is no

longer available for purchase, but continues to be supported.

TL-CCT-0

Metasys

 Controller Configuration Tool (CCT) Software

MS-FCP-0

Metasys

 Field Controller Firmware Package Files for CCT

TP-2420

Transformer, 120 VAC Primary to 24 VAC Secondary, 20 VA, Wall Plug

Y65T31-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount, 8

in. Primary Leads and Secondary Screw Terminals, Class 2

Note: 

Additional Y6x-x Series transformers are also available. Refer to the

Series Y63, Y64, Y65, Y66, and Y69 Transformers Product Bulletin (LIT-125755)

 for

more information.

AS-CBLTSTAT

Cable adapter for connection to 8-pin TE-6700 Series sensors

AS-XFR050-0

Power Transformer (Class 2, 24 VAC, 50 VA Maximum Output), no enclosure

AP-TBK4SA-0

Replacement SA Bus Terminal Blocks, 4-Position, Brown, Bulk Pack of 10

IOM3733 Input/Output Module Installation Guide

12

Summary of Contents for IOM3733

















Reviews: