Appendix 6: Wiring diagrams
Appendix 6: Wiring diagrams
6.1 HS3032, HS3128, and HS3248 UL/ULC wiring diagram (North America only)
Compatible
System Keypads
10.8-12.5V
DC
Bell/Siren
10.8-12.5 V
DC
700mA (max)
Observe Polarity
120 VAC/60 Hz
Primary
18 VDC/65 W
HS65WPSNA
power adapter
NOTE:
For ULC
Commercial Fire Monitoring
applications use Model
HS65WPSNAS.
PGM CONNECTIONS
Earth ground connection
from building electrical
installation.
NOTE:
this ground
connection goes to
HS65WPSNA power
adapter EGND
connections when this
power adapter is mounted
in the cabinet.
550 mA*
(see Aux
wiring
note above)
HS3032/HS3128/HS3248 UL/ULC Wiring Diagram
ULC-LA
(optional)
This device complies with Parts 15 and 68 of the FCC rules.
Operation is subject to the following 2 conditions: [1] this
device may not cause harmful interference and [2] this device
must accept any interference received, including interference
that may cause undesired operation.
Models: HS3032/HS3128/HS3248
US: F53AL01AHS3256 REN = 0.1
Plug Type: RJ-31X
IC: 160A-HS3256
ULC Notes
• For ULC Listed Fire Monitoring Installations & module
requirements, please refer to the ULC Installation
Information Sheet, part number 29010346.
• All tamper circuits may be connected to the same zone.
NOTE:
Refer to Installation Manual for proper battery
capacity selection, based on the intended application.
NOTE:
D
O
not connect power adapter to receptacle
controlled by a switch.
For Fire/Bell wiring refer to Reference Manual.
BATTERY
12V 4.0Ah/7Ah/17Ah
Maximum battery
charge current is
400mA/700mA
(selectable based on
the application. Refer
to Installation Manual)
BATTERY
12V 7Ah
Local Annunciation Devices may be any combination of the keypads:
HS2LCDPRO, HS2TCHPRO(BLK), HS2LCDRFPRO9,
HS2LCDWF(V)PRO9
SIA-FAR Min System Requirements:
1. HS3032/3128 Panel
2. Local annunciation devices
Alarm Bell: Internal BELL output circuit or wireless sirens PG9911 or
PG9901
Remote Transmission: internal DACT or Ethernet or plug-in Cellular
module LE/3G/3H9080
APPLICABLE UL STANDARDS
UL File No. S4019
UL1610
Central Station Burglar Alalrm Units
UL365
Police Station Connected Burglar Alarm Units & Systems
UL609
Local Burglar Alarm Units and Systems
UL985
Household Fire Warning System Units
UL1023
Household Burglar Alarm System Units
UL1635
Digital Alarm Communicator System Units
UL1637
Home Health Care Signaling Equipment
ANSI/SIA CP-01-2014
ULC-S304:16
Standard for Control Units, Accessories and Receiving Equipment for
Intrusion Alarm Systems
ULC-S559-13
Equipment for Fire Signal Receiving Centers and Systems
ULC-S545-02
Residential Fire Warning System Control Units
NOTE:
For UL1637 applications, installation must be done only by a trained installer.
*AUX Wiring
Use No.14-22 AWG conductor.
AUX+ and Corbus (RED) are internally connected.
Total current draw from keypads, PGM Outputs
and AUX circuits must not exceed 2000 mA.
Note:
Refer to the Installation Manual for maximum
current loading levels associated with different
applications.
4-WIRE SMOKE DETECTORS
2-WIRE SMOKE DETECTORS
NOTE:
Refer to Installation Manual & Smoke Detector
Instruction Sheet when locating detectors.
DO NOT
combine
different models on the
same circuit as
operation may be
impaired.
Temperature Range: 0°C-49°C [32°F-120°F] / Maximum Humidity: 93% R.H.
For detailed installation and operating instructions, refer to the Installation Guide #29010135, and the User Manual #29010134. The
HS3032/HS3128/HS3248 is UL Listed for limited energy installations per NEC Article 760. Recognized limited energy cable should be
used. Observe NEC wiring requirements and local codes defined by the authority having jurisdiction. Security detection devices that
require power from the control panel must be UL Listed for the intended application and operate over the range of 10.8-12.5V
DC
. The DSC
Bravo Series are recommended UL Listed motion detectors. Compatible system keypads: HS2LCDPRO, HS2TCHPRO(BLK),
HS2LCDRFPRO9, HS2LCDWF(V)PRO9.
(a)
The delay (power-up) time marked
on the installation wiring diagram of the
smoke detector or on the installed
smoke detector(s) is to be used.
Control panel is suitable for
the following UL installations:
WARNING:
THIS UNIT INCLUDES AN ALARM VERIFICATION FEATURE THAT WILL
RESULT IN A DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED
CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL
NOT EXCEED 60 SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED
TO THESE CIRCUITS UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING
JURISDICTION.
INSTALLATION TYPE
UL/ULC Resi Fire and Burg
UL Local Mercantile
UL Central Station (Burglary)
UL Police Station Connected (Burglary)
ULC Central Station (Burglary)
ULC Central Station Fire Monitoring
SIGNALING MEANS
DACT, PSDN (IP/Cellular Data) NA
DACT (no line security), PSDN (Standard/Encrypted Line Security, use with
Internal Ethernet communicator and/or plug-in cellular module, models
LE/3G/3H9080
DACT (Passive Level P1), PSDN (Passive P1-3/Active A1-4) use with Internal
Ethernet communicator and/or plug-in cellular module, models LE/3G/3H9080
DACT+PSDN (Passive), PSDN (Active), use with Internal Ethernet
communicator and/or plug-in cellular module, models LE/3G/3H9080
25
25
30
30
PG9926/PG9916
Smoke Detector
Circuit
(zone)
Control Unit
Delay - Sec
Models
Delay (seconds)
(a)
(a)
4-Wire UL Listed
FSA-410B /FSA-410BT/
FSA-410BS/FSA-410BST/
FSA-410BLST/FSA-410BR/
FSA-410BRT/FSA-410BRS/
FSA-410BRST/
FSA-410BLRST
4-Wire ULC Listed
FSA-410A/FSA-410AT/
FSA-410AS/FSA-410AST/
FSA-410ALST/FSA-410AR/
FSA-410ART/FSA-410ARS/
FSA-410ARST/
FSA-410ALRST
TYPICAL ZONE CIRCUITS
Single End-of-Line Resistor Wiring
Double End-of-Line Resistor Wiring
Triple End-of-Line
Resistor Wiring
NOTE:
Maximum line impedance 100
3
Mask
/Fault
EOLR-2
END-OF-LINE-
RESISTOR
5600 0.5W
BLK
COM
Zone input
IN
IN
OUT
NO
ALM
OUT
RED
WHT
GRN
Compatible DSC 4-wire
smoke detectors:
FSA-410A Series for ULC
FSA-410B Series for UL
FSA-410C Series for EU
Compatible DSC 2-wire
smoke detectors:
FSA-210A Series for ULC
FSA-210B Series for UL
FSA-210C Series for EU
Smoke detector must
be latching type (e.g.,
DSC FSA-410B Series)
To reset smoke detector,
enter [ * ][7][2]
Alarm
initiating
loop
resistance
100
NAME
DSC
MODEL
FSA-210B
Series
MAX #
DSC
BASE
NONE
COMPATIBILITY ID
FS200
2200
END-OF-LINE
RESISTOR
EOLR-3
Compatibilty Identifier: HS3-1
Maximum Operating Voltage: 13.8 VDC
Maximum Number of Detectors: 18
NOTE:
Refer to the
FSA-210 Installation Manual for more details.
IMPORTANT:
Minimum
6.4 (1/4”) separation
must be maintained
between RM-1 circuits
and all other wiring.
Out to premisis telephone
In from telephone company
RJ-31X Telephone Plug 26 AWG
WARNING:
Not to be removed by anyone except occupant.
This equipment should be installed in accordance with
Chapter 29 of the National Fire Alarm and Signaling Code,
ANSI/NFPA 72, (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269). Printed information
describing proper installation, operation, testing,
maintenance, evacuation planning, and repair service is to
be provided with this equipment. For compliance with
UL985, at least one smoke detector is required. Test the
system at least once per week. The system is intended to
be checked by a qualified technician at least every 3 years.
For UL1637 installations, the test must also be performed
with the AC off, using the standby battery.
MICRO-B
PC LINK
USB TYPE A
LE9080
3G9080
3H9080
PGM
CORBUS
AUX
BELL
DC
AUX
ZONE
ZONE
ZONE
ZONE
TELCO
ETHERNET
BATTERY
UA718
PGM4: 100 mA (max)
PGM3: 300 mA (max)
PGM1: 100 mA (max)
PGM2: 300 mA (max)
All circuits are classified for UL installations as power limited/Class II power limited, except for the
battery leads which are not power limited. Do not route any wiring over circuit boards. Maintain at
least 1” (25.4 mm) separation. A minimum 1/4” (6.4 mm) separation must be maintained at all
points between power limited wiring and all other non-power limited wiring. Inspect wiring and
ensure connections are correct before applying power.
Warning:
Disconnect AC power and
telephone lines before servicing.
Attention:
Débranchez l’alimentation
secteur et lignes téléphoniques avant
l’entretien.
RESISTOR
IDENTIFICATIONS
2-WIRE SMOKE
NOTE:
For UL listed applications, use Model EOLR-1
BELL CIRCUIT
NOTE:
For UL listed applications, use Model EOLR-3
SINGLE ZONE EOL
NOTE:
For UL listed applications, use Model EOLR-2
POWER LIMITED
Cable ties (not supplied) recommended
HS3032 PCB
HS3128 PCB
HS3248 PCB
UA718
MICRO-B
PC LINK
USB TYPE A
4Ah
7Ah
2 x 7Ah
17Ah
Black -
Red +
PGM
CORBUS
AUX
BELL
DC
AUX
ZONE
ZONE
ZONE
ZONE
TELCO
ETHERNET
BATTERY
HS3032/3128/HS3248
PCB current draw= 125
mA alarm current=700 mA
UL Resi Burg
ULC Resi Burg
UL COM Burg
UL Resi Fire
UL, HH, ULC Resi Fire
ULC Com Burg
EN50131
Grade 2
EN50131
Grade 3
Power supply adapter
HS65WPSNA
HS65WPSNA
HS65WPSNA
HS65WPSNAS (ULC CB
Security Level 4. Require
High Voltage Barrier Kit)
HS65WPS
HS65WPS
Battery capacity/
max loading
4 Ah/700 mA
7 Ah/1200 mA
14 Ah/2000 mA
17 Ah/2000 mA
4 Ah/700 mA
7 Ah/1200 mA
14 Ah/2000 mA
17 Ah/2000 mA
7 Ah/250 mA
14 Ah/500 mA
17 Ah/600 mA
17 Ah/1200 mA 17 Ah/500 mA
Standby time + alarm time
12 hours
30 hr (AC fail
transmission)
24 hr + 4 min
24 hr + 5 min
24 hr + 4 min
Recharging current
setting
Low (400 mA)
High (700 mA)
High (700 mA)
High (700 mA)
Low (400 mA)
High (700 mA)
Low (400 mA)
4 hr + 15 min
4 hr + 4 min
4 hr + 5 min
ULC COM
fire
Monitoring
HS65WPSNAS
14 Ah/500 mA
17 Ah/600 mA
24 h + 30 min
High (700 mA)
UL Resi Fire with
wired CO Detectors
UL985 6th Ed
HS65WPSNA
14 Ah/330 mA
17 Ah/400 mA
24 h + 4 min +
12 hr CO Alarm
High (700 mA)
Enclosure
HSC3010C
HSC3020C
HSC3020C
HSC3030CAR
HSC3010C
HSC3010CR
HSC3010C
Not required for UL/ULC.
AC wiring details for ULC-561 using HSC3010CR
enclosure
Use metal standoff and screw in the position indicated.
IMPORTANT! Ensure screw and standoff are tightly
secured ot establish Earthground connection for the
PCB.
Lorem ipsum
- 276 -
