Johnson Controls FX70 Installation Instructions Manual Download Page 20

Page: 20 / 21

FX70 Supervisory Controller Installation Instructions

Reconnect the earth ground wire to the controller’s
grounding lug and any installed accessory
modules.

10. Reconnect any Ethernet, serial, modem, and I/O

connectors.

11. If using IO modules, and any of your I/O points

have voltage, turn the devices back on, or
reconnect power to them.

12. Replace the cover. See

Removing and Replacing

the Cover

on page 6.

13. Restore power to the unit. It should boot up as a

new unit (see

Check the Status LED

on page 16).

14. Use FX Workbench to re-commission the FX70

and install the saved station database.

COM Slot Assignments

Table 6 lists the COM slot assignments for the FX70
Controller.

Table 6: COM Slot Assignments for the FX70 Supervisory Controller (Part 1 of 2)

Option Slot 1

Option Slot 2

Onboard RS-232

Onboard RS-485

None

COM1

COM2

RS-232 = COM5

None

COM1

COM2

RS-232 = COM5

RS-232 = COM6

COM1

COM2

RS-232 = COM5

RS-485 = COM6, COM7

COM1

COM2

RS-232 = COM5

LON = LON1

COM1

COM2

RS-232 = COM5

Sedona = COM6

COM1

COM2

RS-232 = COM5

Modem = COM4

COM1

COM2

RS-232 = COM5

GPRS = COM6, COM7

COM1

COM2

RS-485 = COM5, COM6

None

COM1

COM2

RS-485 = COM5, COM6

RS-232 = COM7

COM1

COM2

RS-485 = COM5, COM6

RS-485 = COM7, COM8

COM1

COM2

RS-485 = COM5, COM6

LON = LON1

COM1

COM2

RS-485 = COM5, COM6

Sedona = COM7

COM1

COM2

RS-485 = COM5, COM6

Modem = COM4

COM1

COM2

RS-485 = COM5, COM6

GPRS = COM7, COM8

COM1

COM2

LON = LON1

None

COM1

COM2

LON = LON1

RS-232 = COM5

COM1

COM2

LON = LON1

RS-485 = COM5, COM6

COM1

COM2

LON = LON1

LON = LON2

COM1

COM2

LON = LON1

Sedona = COM5

COM1

COM2

LON = LON1

Modem = COM4

COM1

COM2

LON = LON1

GPRS = COM5, COM6

COM1

COM2

Sedona = COM5

None

COM1

COM2

Sedona = COM5

RS-232 = COM6

COM1

COM2

Sedona = COM5

RS-485 = COM6, COM6

COM1

COM2

Sedona = COM5

LON = LON1

COM1

COM2

Sedona = COM5

Modem = COM6

COM1

COM2

Sedona = COM5

GPRS = COM6,COM7

COM1

COM2

Modem = COM3

None

COM1

COM2

Modem = COM3

RS-232 = COM5

COM1

COM2

Modem = COM3

RS-485 = COM5, COM6

COM1

COM2

Modem = COM3

LON = LON1

COM1

COM2

Modem = COM3

Sedona = COM5

COM1

COM2

Summary of Contents for FX70






















Search results

Summary of Contents for FX70

Reviews:

Related manuals for FX70

Brands by name

Popular brands

Johnson Controls FX70, Installation Instructions Manual

Search results

Summary of Contents for FX70

Reviews:

Related manuals for FX70

Brands by name

Popular brands