Joab EcoDrive Operation And Maintenance Manual Download Page 60 | Manualshive

Page: 60 / 73

background image

5.

Verify that all lighting and other electrical
equipment functions correctly.

6.

Finish by inspecting the hydraulic pump.

If any damage is found, contact your JOAB workshop imme-
diately.

Washing the Hook-Lift

Newly lacquered surfaces must be cleaned
using detergent and a sponge only. Do not use
a high pressure washer. A high pressure
washer should only be used after at least three
weeks following treatment of surfaces.

Detergents contain acids. Make sure that the
cleaning fluid used to clean surfaces contains
less than 9pH. The maximum temperature of
the cleaning fluid must not exceed 50 °C above
the ambient temperature. After washing, make
sure to rinse all surfaces thoroughly.

Cleaning the hook-lift with a high pressure washer entails risks. All electrical components, even
enclosed, are sensitive to water under high pressure.

When using a high pressure washer, make sure to hold the nozzle at least 45 cm from all
lacquered surfaces. Use a standard nozzle only, do not use a turbo nozzle.

Always apply fresh grease around lubrication points after washing. For more information
regarding the hook-lift's lubrication points, refer to below.

52

Service and Maintenance | Washing the Hook-Lift

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
58
59
60
61
62
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: Paton Pages: 31

Brand: Simplex Pages: 40

Brand: Wenshing Pages: 4

Brand: ubbink Pages: 61

NeverFreeze SX-0810-24

Brand: ThermoSoft Pages: 5

Brand: Mobile Industrial Robots Pages: 73

Brand: HEIN-WERNER AUTOMOTIVE Pages: 12

Brand: M-system Pages: 10

SwitchPoint Infinity 3

Brand: Stryker Pages: 124

bryant ONEBB3ZAC01

Brand: Carrier Pages: 6

Brand: ESAB Pages: 44

AlumaPower 450 MPa

Brand: Miller Pages: 48

Brand: Sel Pages: 12

Ricon FoldOver FR2SS Series

Brand: Wabtec Pages: 85

PILOT 161 AC/DC

Brand: Migatronic Pages: 48

Brand: btsr Pages: 71

Brand: morse Pages: 6

Brand: morse Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands