Joab EcoDrive Operation And Maintenance Manual Download Page 47 | Manualshive

Page: 47 / 73

background image

39

Tipping a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

To tip a body follow the procedure listed below:

1.

Make sure that there is nobody within the working area of the vehicle and the body.

2.

Make sure that the vehicle is on a level and firm surface.

Failure to do so, can lead to the vehicle being unevenly loaded and tipping over. If the
vehicle leans two or more degrees there is a risk that it will tip over.

3.

If the vehicle has retractable axles, make
sure that they are lowered before tipping.

4.

Start the hydraulic pump. Once the pump is
started, the pump icon will be displayed in
the CBW controller as shown.

For information regarding the starting of the
pump, refer to

"User Interface", on page 12

.

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
45
46
47
48
49
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

PACSystems RX7i

Brand: GE Pages: 317

Brand: OMA Pages: 73

DBI SALA Pro Series

Brand: 3M Pages: 24

Brand: Parkside Pages: 94

PLATINUM PS-9003

Brand: HydroQuip Pages: 24

Heat Control System

Brand: ORTAL Pages: 20

CoolBloC C34 DN 32

Brand: PAW Pages: 24

Brand: National Instruments Pages: 13

Trailblazer 251

Brand: Miller Pages: 48

USB-1408FS-Plus-OEM

Brand: Measurement Computing Pages: 26

Brand: JAMO Pages: 18

WALLACE & TIERNAN SFC SC

Brand: Evoqua Pages: 82

Brand: Thiele Pages: 5

Brand: BorMann Pages: 33

Brand: Westken Pages: 11

Brand: M-system Pages: 4

Brand: Migatronic Pages: 106

TOP LIFT TSK 12000 DJ

Brand: Nussbaum Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands