Joab EcoDrive Operation And Maintenance Manual Download Page 41 | Manualshive

Page: 41 / 73

background image

33

Loading a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

Before loading a body, refer to and read the information provided under

"Distributing a Load on

a Body", on page 31

To load a body, follow the procedure listed below:

1.

Visually inspect the load and make sure
that it is evenly distributed.

2.

Make sure that there is nobody within the
working area of the vehicle and the body.

3.

Start the hydraulic pump. Once the pump is
started, the pump icon will be displayed in
the CBW controller as shown.

For information regarding the starting of the
pump, refer to

"User Interface", on page 12

.

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
39
40
41
42
43
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: Danfoss Pages: 28

Brand: Orion Welders Pages: 51

Brand: ESAB Pages: 23

Brand: Contec Pages: 7

Brand: Migatronic Pages: 28

Brand: Nedap Pages: 5

Brand: Everlast Pages: 30

Brand: WAGO Pages: 20

Brand: Daikin Pages: 36

Brand: Contec Pages: 65

Brand: American Panel Pages: 18

Brand: Miller Pages: 44

Brand: Balluff Pages: 42

Brand: HEIDENHAIN Pages: 98

Brand: Lincoln Electric Pages: 85

RIS 5500HE EKO 3.0

Brand: Salda Pages: 38

Brand: Contec Pages: 67

Smootharc Elite MIG 451 Progress Pulse

Brand: BOC Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands