Joab EcoDrive Operation And Maintenance Manual Download Page 27 | Manualshive

Page: 27 / 73

background image

Side plough

IN

Front plough

DOWN

Push the knob left

Push the knob forwards

Table 5: CBW controller stick - snow plough functions (continued)

Diagnostics and Statistics

The CBW controller has a diagnostic and statistics page that the user can view. The information
provided in this page includes:

1. Time that the system has been active.

2. Time the power has been active.

3. The number of shunts done.

4. The number of tips done.

5. The software version (not all units).

6. Which sensor is active.

7. Control stick diagnostic information.

8. Certain installations packets.

9. Diagnostic information for outputs.

To access the menu, first make sure that one of
the main menu pages is displayed and then
press and hold down the OK button for a few
seconds. The screen shown opposite will then
be displayed.

Use the arrow buttons to navigate the menu.
The up and down arrow buttons navigate
through the menu. The left and right arrow but-
tons allow the user to select from options when
applicable.

To exit the diagnostic and statistical menu,
press and hold down the OK button for a few
seconds.

Continuous-Hydraulic-Supply

The CBW controller can be used to set and adjust a

constant

hydraulic feed to a tip-trailer. This

is not standard, it must be ordered as an extra option.

19

Operation | CBW controller

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
25
26
27
28
29
...
»

Summary of Contents for EcoDrive










































































Reviews:

No comments

Related manuals for EcoDrive

Brand: ShoreStation Pages: 15

Brand: Skyjack Pages: 47

Foxtrot C-IT-0908S

Brand: TECO Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: WesAudio Pages: 65

SPACOMMAND CP3800 Series

Brand: Pentair Pages: 36

Brand: Presto Lifts Pages: 18

Compute Module IO Board Plus

Brand: Waveshare Pages: 17

Brand: Telwin Pages: 36

Hurricane Zephyr HW

Brand: ITR Pages: 89

Brand: Riello Pages: 20

Brand: STAMOS Pages: 9

Brand: STAMOS Pages: 7

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: pewag Pages: 24

Brand: Würth Pages: 101

Brand: Craftsman Pages: 8

Brand: Craftsman Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands