Jntech JNP11KH-V4 Quick Installation Download Page 6

Page: 6 / 76

2 Installation

2.1 Prepare Installation Tools

The following tools will be needed in inverter installation and wire connection.

Sketch map

Name

Recommend

specification

Function

Wire crimpers

M2.5~M8

Crimp the PV cable core in
connector tube for PV
connector.

Electric drill

Ф8

Used for drilling holes for
installation bracket.

Straight
screwdriver

Ф3

Used for AC side wire
installation

Cross
screwdriver

Ф5

Used for installing and
disassembling inverter cover

2.2 Installation Direction and spacing dimension

The inverter shall be installed vertically or tilted backwards with a maximum

angle of 10°

The minimum installation spacing dimensions are shown below:

Direction

Minimum spacing

Direction

Minimum spacing

Above

100cm

Sides

100cm

Below

100cm

Front

100cm

Summary of Contents for JNP11KH-V4













































































Search results

Summary of Contents for JNP11KH-V4

Reviews:

Related manuals for JNP11KH-V4

Brands by name

Popular brands

Jntech JNP11KH-V4, Quick Installation

Search results

Summary of Contents for JNP11KH-V4

Reviews:

Related manuals for JNP11KH-V4

Brands by name

Popular brands