JLG 3513PS Operation & Safety Manual Download Page 31 | Manualshive

Page: 31 / 70

background image

Section 2 - Pre-Operation and Inspection

2-11

31200345

2.6

LANYARD ANCHORAGE POINTS

• Attach lanyard to one of the lanyard anchorage points.

• Fixed Platform - Attach one lanyard per lanyard anchorage point. DO NOT attach more

than one lanyard per lanyard anchorage point.

• Extendable Platform - Attach two lanyards per lanyard anchorage point. DO NOT

attach more than two lanyards per lanyard anchorage point.

O

Z

1290

«
...
29
30
31
32
33
...
»

Summary of Contents for 3513PS







































































Reviews:

No comments

Related manuals for 3513PS

Brand: Keg King Pages: 4

Brand: Vestil Pages: 8

Brand: Bard Pages: 54

Brand: Lampert Pages: 22

NeverFreeze SX-0810-24

Brand: ThermoSoft Pages: 5

CompuScope 85GC

Brand: Gage Pages: 174

Brand: Genie Pages: 44

Brand: gala gar Pages: 28

Brand: Dometic Pages: 24

Digital Car Puller 5000

Brand: Telwin Pages: 104

Brand: Urrea Pages: 12

Brand: Champion Autolift Pages: 14

Brand: Solter Pages: 16

Brand: National Instruments Pages: 265

Brand: Avers Screens Pages: 12

Brand: Adam Hall Pages: 27

Brand: Siemens Pages: 32

SIMATIC Ident CB Gate

Brand: Siemens Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands