SECTION 2 - PROCEDURES
3120826
– JLG Sizzor –
2-9
Cleaning and Inspection
1.
Clean all parts thoroughly in an approved cleaning
solvent.
2.
Inspect the cylinder rod for scoring, tapering, ovality,
or other damage. If necessary, dress rod with
Scotch Brite or equivalent. Replace rod if necessary.
3.
Inspect threaded portion of rod for excessive dam-
age. Dress threads as necessary.
4.
Inspect inner surface of cylinder barrel tube for scor-
ing or other damage. Check inside diameter for
tapering or ovality. Replace if necessary.
5.
Inspect threaded portion of barrel for damage. Dress
threads as necessary.
6.
Inspect piston surface for damage and scoring and
for distortion. Dress piston surface or replace piston
as necessary.
7.
Inspect seal and o-ring grooves in piston for burrs
and sharp edges. Dress applicable surfaces as nec-
essary.
8.
Inspect cylinder head inside diameter for scoring or
other damage and for ovality and tapering. Replace
as necessary.
9.
Inspect seal and o-ring grooves in head for burrs
and sharp edges. Dress applicable surfaces as nec-
essary.
10.
If applicable, inspect cylinder head retainer or end
cap for surface or thread damage. Repair or replace
as necessary.
11.
Inspect cylinder head outside diameter for scoring
or other damage and ovality and tapering. Replace
as necessary.
12.
If applicable, inspect thread ring for scoring or other
damage. Dress threads or applicable surfaces as
necessary.
13.
If applicable, inspect rod and barrel bushings for
signs of correct lubrication and excessive wear.
Replace as necessary.
14.
Inspect travel limiting collar or spacer for burrs and
sharp edges. If necessary, dress inside diameter
surface with Scotch Brite or equivalent.
15.
If applicable, inspect port block fittings and holding
valve. Replace as necessary.
16.
Inspect the oil ports for blockage or the presence of
dirt or other foreign material. Repair as necessary.
17.
If applicable, inspect piston rings for cracks or other
damage. Replace as necessary.
Assembly
NOTE: Prior to cylinder assembly, ensure that the proper
cylinder seal kit is used.
Apply a light film of hydraulic oil to all components
prior to assembly.
1.
Place a new wiper seal and rod seal into the applica-
ble cylinder head gland grooves.
Use a soft mallet to tap a new wiper seal into the applica-
ble cylinder head gland groove.
WHEN INSTALLING NEW “POLY-PAK” TYPE PISTON SEALS
(AXLE LOCKOUT CYLINDER), ENSURE SEALS ARE INSTALLED
PROPERLY. REFER TO FIGURE 2-11 FOR CORRECT SEAL ORIEN-
TATION. IMPROPER SEAL INSTALLATION COULD RESULT IN
CYLINDER LEAKAGE AND IMPROPER CYLINDER OPERATION.
Figure 2-9. Rod Seal Installation
Figure 2-10. WIper Seal Installation
Summary of Contents for 25RTS
