Jinhan JHJDS30 series Manual Download Page 1

1

Foreword

Dear users

Hello

Thank you for purchasing a new handheld oscilloscopes from Jin Han electronic.

In order to properly

use this instrument

please read the full text of this manual carefully before using the instrument

especially about the "safety precautions" part.If you have finished reading this specification

we

recommend that you instructions for proper custody

together with the instrument placed or placed where

you can access at any time

For future inspection during use.

Copyright Information

Hefei Jin Han Electronic Technology Co., Ltd. All rights reserved.
Jin Han-electronic products by China or other countries patent protection

including been made or pending

patent applications.The Company reserves have to change product specifications and prices right.Jin Han
All rights reserved.Licensed software products are all made of Jin Han

protected by national copyright

laws and international treaty provisions.

If the original purchaser from the date of purchase of the product within two years, the products are sold

or transferred to third parties, the warranty period shall be the date of the products from the original buyer of

Summary of Contents for JHJDS30 series


















































































Reviews: