manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

Using the System

 

51

Parameter Name

Description

Syslog Debug

Enable syslog debug or not

Syslog Debug Server IP

The syslogd server to receive the debug information.
The port to receive the syslog is 514.

Trace Target

The target to be used for debugging. It could be the
telephony number or IP address. You can combine it
by using a semicolon to separate it. For example, you
can have the trace target as "02123456;112.112.1.1"
which indicates the debug message will contains the
calling or called number is 02123456 or IP address is
112.112.1.1.

Debug Level

This parameter is the detail level of generating debug
information. The default level is "Warning". When you
change it to  debug, the system will generate hug log
and might greatly affect the system performance.
Please only change it under the supervision of FAE.

Module List

The target module to be debug. Please only change it
under the supervision of FAE.

2.2.11 System Alert

The system can be set to  automatically send the system event notice to
administrator through syslog or email. Click 

SYSTEM -> System Alert 

to view and

change the settings.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Tadiran Telecom Coral IPx 500 Installation Manual preview
Coral IPx 500
Brand: Tadiran Telecom Pages: 544
SpectraLink Link 3000 MCU Installation Manual preview
Link 3000 MCU
Brand: SpectraLink Pages: 54
CommTech CT100 Installation Manual preview
CT100
Brand: CommTech Pages: 15
Panasonic KX-NCP500 Features Manual preview
KX-NCP500
Brand: Panasonic Pages: 468
Panasonic KX-NS1000 Manual preview
KX-NS1000
Brand: Panasonic Pages: 542
Xorcom XE Series User Manual preview
XE Series
Brand: Xorcom Pages: 6

Brands by name

Popular brands

Load more brands