manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

 

 

44

Parameter Name

Description

Database CDR

If it is enabled, the system will do the local billing
calculation. It will store call detail into local database
and use the tariff plan to calculate the charge amount.
And you will able to see the top usage or division
report from the Billing.

2.2.5

Auto Provisioning

The system can support CPE auto provisioning. Please contact technical support for
supported model. Click SYSTEM -> Auto Provisioning and the following will appear:

Parameter Name

Description

SIP Multicasting Provision

Whether to enable SIP multicasting (SIP pnP) for
searching SIP provisioning server or not.  

Attached Interface

Which interface will be serviced for SIP multicasting
service. Because normally multicasting package
cannot over layer 3 network. Thus this is normally
service at LAN interface.

Unassigned Mac Keep
Time (minutes)

How long the unassigned mac address will be kept in
the system for assignment? Within this period, the
unassigned mac with line ID will be found in the
Diagnostic -> Unassigned Mac List

Provisioning DNS for
WAN

When this parameter was set, the provisioned config
URL will be used for this DNS name instead of IP
address. 

NTP Server 1/2

The NTP server 1 will be used for CPE. Check User
Proxy IP if SIP proxy or PBX do provide NTP
service. 

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

H3C XE 200/2000 IP Operation Manual preview
XE 200/2000 IP
Brand: H3C Pages: 514
Panasonic KX-TDA100AL Service Manual preview
KX-TDA100AL
Brand: Panasonic Pages: 125
Nortel QBL16 Manual preview
QBL16
Brand: Nortel Pages: 46
Nortel Succession 1000M System Overview preview
Succession 1000M
Brand: Nortel Pages: 48
Nortel TFC002 Manual preview
TFC002
Brand: Nortel Pages: 67
Nortel Contact Center Manager Installation And Maintenance Manual preview
Contact Center Manager
Brand: Nortel Pages: 1618

Brands by name

Popular brands

Load more brands