JING JIE UniPBX-2000 Administrative Manual Download

Page: 36 / 219

2.2.1.1

TLS Certficate Upload

This is used to upload the SIP required TLS certificate. Click TLS Certificate Upload
button to upload the certificate for SIP TLS service.

2.2.1.2

SIP Reject Code

This is a mapping table for SIP Proxy reject reason code.

The detail of each parameter is described as below:

Parameter Name

Description

Description for SIP
Reject Reason

The description of SIP reject reason. Please contact
FAE if need more inmation

SIP Reason Code

Which reason code will be return to CPE

2.2.2

Service Parameter

The Service Parameters including some default setting of SIP service. Click

SYSTEM -> Service Parameter

to view and change the settings.

Summary of Contents for UniPBX-2000




























































































































































































































Search results

Summary of Contents for UniPBX-2000

Reviews:

Related manuals for UniPBX-2000

Brands by name

Popular brands

JING JIE UniPBX-2000, Administrative Manual

Search results

Summary of Contents for UniPBX-2000

Reviews:

Related manuals for UniPBX-2000

Brands by name

Popular brands