manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

 

 

184

4.7.3

Meet Me Conference

By using your smart phone, you can manage the meeting me conference from
anywhere. Click Meet Met Conference and the following will appear.

Enter the monitored meet me conference room number and host PIN code, press
Enter and the following will appear.

The above had 2 participants are joined, you can use the following to control the
conference room.

 Mute the participant or whole conference room.

Un-mute the participant or whole conference room.

Disconnect the user from the conference room.

Quit the meet me conference control and back to menu.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Panasonic KX-TD816 Features Manual preview
KX-TD816
Brand: Panasonic Pages: 290
Epygi Quadro Quadro 4x Specifications preview
Quadro Quadro 4x
Brand: Epygi Pages: 2
NEC XN120 2OPBOX Manual preview
XN120 2OPBOX
Brand: NEC Pages: 8
SMC Networks PBX10 FICHE User Manual preview
PBX10 FICHE
Brand: SMC Networks Pages: 132

Brands by name

Popular brands

Load more brands