manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

 

 

162

Field Name

Description

Peak Meet Me
Conference

The peak service count for meet me conference
service.

Total Meet Me
Conference

The total service count for meet me conference within
this period.

Call Park

The service count for call park service

Peak Call Park

The peak service count for call park service

Total Call Park

The total service count for call park service within this
period.

Adhoc Conference

The service count for adhoc conference service.

Peak Adhoc Conference

The peak service count for adhoc conference service.

Total Adhoc Conference

The total service count for adhoc conference service
within this period.

Ext2Ext VMS

The service count for extension to extension voice mail
or direct to voice mail service.

Peak Ext2Ext VMS

The peak service count for extension to extension
voice mail or direct to voice mail service.

Total Ext2Ext VMS

The total service count for extension to extension voice
mail or direct to voice mail service.

2.7.8

Ping

The administrator can ping a IP address from the host  by clicking

 DIAGNOSTIC ->

Ping.

 The following screen will appear.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Epygi Quadro Quadro 4x Specifications preview
Quadro Quadro 4x
Brand: Epygi Pages: 2
IKE TC-2000 Seires Manual preview
TC-2000 Seires
Brand: IKE Pages: 37
Wahsega Carina PBX Installer'S Manual preview
Carina PBX
Brand: Wahsega Pages: 8
Panasonic KX-TDE200 Getting Started preview
KX-TDE200
Brand: Panasonic Pages: 30
VoLANs VoSS12 Admin Manual preview
VoSS12
Brand: VoLANs Pages: 127
Telco Depot TD100 SERIES User Manual preview
TD100 SERIES
Brand: Telco Depot Pages: 71
MCK EXTender 4000 Quick Installation Manual preview
EXTender 4000
Brand: MCK Pages: 24
MCK EXTender PBXgateway II Quick Installation Manual preview
EXTender PBXgateway II
Brand: MCK Pages: 58

Brands by name

Popular brands

Load more brands