manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

Using the System

 

159

Field Name

Description

IPV4 VIP for WAN

Virtual IP V4 address for WAN interface for HA Group 2.

IPV4 VIP for LAN

Virtual IP V4 address for LAN interface for HA Group 2.

IPV6 VIP for WAN

Virtual IP V6 address for WAN interface for HA Group 2. The
IPV6 address must be a global unicast addressed, not a link-
local or site-local address. IPV6 VIP for WAN is only available
when 1 Ethernet leg mode is used (Attached LAN Interface is
disabled).

IPV6 VIP for LAN

Virtual IP V6 address for WAN interface for HA Group 2.
Virtual IP V6 address for WAN interface. The IPV6 address
must be a global unicast addressed, not a link-local or site-
local address. It could be use fc00:xxxx:xxx:xxx as the private
IP V6 address. IPV6 VIP for LAN is only available when 2
Ethernet legs mode is used (Attached LAN interface is
enabled).

Service Controller

It is a internal status for HA resource status controlling.

2.7.5

Blocked IP

The system will detect the SIP attack such as "friendly scanner" or other potential
attack by the attacking behavior and blocked it automatically. A system alert event
will be written to system alert for auditing purpose.   After the defined "Attack Block
Time" in Service Parameter is reached, the blocked IP will be released. The
administrator can query the current blocked IP address by clicking

 DIAGNOSTIC ->

Blocked IP

. The following screen will appear.

The detail of each filed is described as below:

Field Name

Description

IP Address

The IP address was blocked by the system because of
SIP attack detected.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Aastra OpenCom 100 series Short Installation Manual preview
OpenCom 100 series
Brand: Aastra Pages: 2
Samsung OfficeServ 7100 Series System Description preview
OfficeServ 7100 Series
Brand: Samsung Pages: 113
WELLTECH ePBX40 User Manual preview
ePBX40
Brand: WELLTECH Pages: 130
MCK EXTender 4000 Quick Installation Manual preview
EXTender 4000
Brand: MCK Pages: 24
MCK EXTender PBXgateway II Quick Installation Manual preview
EXTender PBXgateway II
Brand: MCK Pages: 58

Brands by name

Popular brands

Load more brands