manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

Using the System

 

157

Field Name

Description

Calling

The calling party number

Called

The called party number

State

The current call state

Connect Time

The connected time for the call

Call ID

The SIP call ID 

2.7.4

High Available Status

The HA status can be checked by click 

DIAGNOSTIC -> High Available Status

. If

both server are working correctly, you could see that the status of each HA member
is "online" as follows:

The detail of each filed is described as below:

Field Name

Description

Cluster ID

Cluster ID is used to identify the cluster. Different Cluster ID
will not able to working together. For different Cluster ID, it is
required to use different Cluster Service Port. The maximum
length of ID is 6 bytes.  

Cluster Service
Port

The UDP port will be used for intra-cluster communication to
send and receive heartbeat message. It is required to have
different Cluster Service Port for each Cluster ID. The default
value is 694.

Cluster Type

The following types are supported to meet different
requirements:

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Brands by name

Popular brands

Load more brands