manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

Using the System

 

129

2.4.11 Queue Prompt

The system support call queue feature. The max call queue can be supported is
1000, starting from 000 to 999. You need config call queuing feature in Routing Plan
to enable call queuing feature. Here is the place to put the required queue prompts.
There are 2 prompts for each call queue. The "Play Once Prompt" will be play once
at first and play the "Continue Play Prompt" till the call is connected or disconnected.
Click FEATURE-> Queue Prompt and the following screen will appear.

The file format is showed as follows:
- 8K Sample Rate
- 16 bits
- Linear PCM (signed)
- Mono 
- Wav format

Click New to add a new queuing prompt and the following screen will appear.

The detail of each parameter is described as below:

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

NEC SL1100 Adminstrators Manual preview
SL1100
Brand: NEC Pages: 33
NEC ASPILA EX Hardware Manual preview
ASPILA EX
Brand: NEC Pages: 186
Panasonic KX-NCP500 Manual Manual preview
KX-NCP500
Brand: Panasonic Pages: 376
Panasonic KX-TDA200AL Brochure & Specs preview
KX-TDA200AL
Brand: Panasonic Pages: 16
Synway IPPBX Series Hardware Manual preview
IPPBX Series
Brand: Synway Pages: 7
Quadro Quadro6L Manual preview
Quadro6L
Brand: Quadro Pages: 57

Brands by name

Popular brands

Load more brands