manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

Using the System

 

127

The detail of each parameter is described as below:

Parameter Name

Description

DID Number

DID number to be routed

Routed Extension

When system receive this DID number, which extension is
going to be routed. If the routed extension type is phone/
ATA, the called will be replaced to the extension tel
number in order to reach the phone or ATA. Or the original
called number (DID) will be used for call.

Description

The description for this DID number

2.4.10 Voice Logging Target

The voice logging service requires additional license to run. Please contact "Jing
Jie" for detail. You can define an extension to do the recording or record by using a
calling or called number. Here is the place to define which telephone number will be
recorded.  Click

 FEATURE -> Voice Logging Target 

 to view the current settings.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Panasonic KX-TDE Configuration Manual preview
KX-TDE
Brand: Panasonic Pages: 13
AGFEO AS 100 IT Manual preview
AS 100 IT
Brand: AGFEO Pages: 204

Brands by name

Popular brands

Load more brands