JING JIE UniPBX-2000 Administrative Manual Download | Manualshive

Page: 109 / 219

background image

Using the System

109

Parameter Name

Description

Hunting No-Answer
Timer

No answer time out in seconds for this route. The
default value is " Use Global Setting" which means use
the global setting in SYSTEM-> Service Parameter.

SIP Request Response
Timer

SIP Request response time out for this route. The
default value is " Use Global Setting" which means use
the global setting in SYSTEM-> SIP Timer.

Call Queuing

Whether enable call queue feature or not? If it is
enabled and all extensions are not able to answer the
call, the call will be put on queue and call queue music
will be played. There are 2 prompts will be played. The
first prompt is xxx_0.wav which will be played once and
repeat play the xxx_1.wav after it. xxx is the queuing
music ID.

Queuing Music ID

There are 2 prompts will be played for each queue. The
first prompt is xxx_0.wav which will be played once and
repeat play the xxx_1.wav after it. xxx is the queuing
music ID.

Forward BLF

Whether to forward BLF to this routing prefix if it is
matched. It is used only when this routing is to VMS and
is for call park and working hour BLF.

Routing Failure
Extension Number

If all of entries for route cannot be reached or stopped,
here is the last destination to be routed. This is normally
to route to an voice mail such *521234 or a a mobile
such as 092322221111.

Description

The description for this route

2.4.2.1

Hunting Stop Code

For the routing plan which hunt type is "load balance" mode, the

Hunting Stop

Code

is used to quit the hunting. It is typical be used when the system had multiple

gateway or carrier. Normally, when a gateway return with the reason code of busy or
gone, the system should normally stop the hunting. It indicates the user might be busy
or cannot be reached, route to next gateway or carrier will not help also. Hunting
Stop Code could be changed to meet the different hunting requirements:

Click

Hunting Stop Code

button after enter the modification page of a routing plan.

The following web page will appear:

«
...
107
108
109
110
111
...
»

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

Fritz!Box Fon WLAN7170

Brand: AVM Pages: 140

Brand: Toshiba Pages: 368

CompletePBX CXE2000

Brand: Xorcom Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands