manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

The JING JIE UniPBX-2000 is a powerful communication system designed for businesses of all sizes. To effectively manage and configure this advanced device, make sure to download the convenient Administrative Manual from our website. This comprehensive manual is available for free and provides detailed instructions on maximizing the functionality of your UniPBX-2000.

Share
Download
background image

 

 

106

Parameter Name

Description

SIP Trunk ID

SIP trunk ID 

SIP Domain

The  SIP register domain for SIP trunk user

Register TEL

The SIP User (normally, it is TEL number)  for register 

Registrar Server

The SIP registrar proxy server IP address or DNS name.

Registrar Port

The SIP service  port to register (default value is 5060)

Outbound Proxy
Server

The SIP outbound proxy IP address or DNS name

Outbound Proxy Port

The outbound proxy service port (default value is 5060)

SIP Register User ID

The SIP user ID for authentication

SIP Register
Password

The SIP password for authentication

Register Expires
Time

The register expires in seconds for SIP register. The
default is 600 seconds. 

Permanent Contact

If this is checked, this SIP trunk will no register and use
peering instead.

Display Name of SIP
Trunk

The SIP Display Name will be used when this SIP trunk is
calling. The default is original caller's SIP TEL.

SIP ANI of SIP Trunk

The SIP TEL will be used when this SIP trunk is calling.
The default is SIP trunk's TEL.

Local Port

The local SIP port will be used for this SIP trunk. For most
of case, it will be 5060 port.

Description

The description for this SIP trunk

2.4.2

Routing Plan

The routing plan is used to provides different routing based on prefix, time of day,
dialed length and hunting type to decide where the call should be called.  The
maximum Routing Plan could be created is 4096. Click

 FEATURE -> Routing Plan

to view the current created routing plans as follows:

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Related manuals for UniPBX-2000

CCL COX-16120S Operating & Programming Manual preview
COX-16120S
Brand: CCL Pages: 18
Planet IPX-1980 User Manual preview
IPX-1980
Brand: Planet Pages: 88
Nortel Compact ICS Telephone Feature Card Manual preview
Compact ICS Telephone Feature Card
Brand: Nortel Pages: 12

Brands by name

Popular brands

Load more brands