manualshive.com logo in svg

Jetter JX3-BN-CAN, User Manual

Share
Download
Jetter JX3-BN-CAN User Manual Download Page 45

JX3-BN-CAN 

Appendix

 

 

 

 

 

 

10.4  Shielded Data and I/O Lines 

 

Operating Parameters (EMC) - Immunity to Interference

Parameters Value(s) 

Standard 

Asymmetric RF, 
amplitude-modulated 

Frequency band 0.15 - 80 MHz 
Test voltage 3 V 
AM 80 % with 1 kHz 
Source impedance 150 Ohm 
Criterion A 

DIN EN 61131-2 
DIN EN 61000-6-2 
DIN EN 61000-4-6 

Burst  
(Bursts) 

Test voltage 1 kV 
tr/tn 5/50 ns 
Repetition rate 5 kHz 
Criterion A 

DIN EN 61131-2 
DIN EN 61000-6-2 
DIN EN 61000-4-4 

Voltage Surges, 
asymmetric  
(line to earth) 

tr/th 1.2/50 µs 
Common mode launching 1 kV 

DIN EN 61131-2 
DIN EN 61000-6-2 
DIN EN 61000-4-5 

 
 

Operating Parameters EMC - Immunity to Interference 

Functional Ground Connection 

Parameters Value(s) 

Standard 

RF, asymmetric 

Frequency band 0.15 - 80 MHz 
Test voltage 3 V 
AM 80 % with 1 kHz 
Source impedance 150 Ohm 
Criterion A 

DIN EN 61131-2 
DIN EN 61000-6-2 
DIN EN 61000-4-6 

Bursts 

Test voltage 1 kV 
tr/tn 5/50 ns 
Repetition rate 5 kHz 
Criterion A 

DIN EN 61131-2 
DIN EN 61000-6-2 
DIN EN 61000-4-4 

 

 

 

 
 

    Jetter AG 

45 

Summary of Contents for JX3-BN-CAN























































Reviews:

No comments

Brands by name

Popular brands

Load more brands