Jetter JetMove 208-480 User Manual Download Page 93

Page: 93 / 124

JetMove 208-480

12 Ethernet Interface (Option)

Jetter AG

Ethernet Interface (Option)

12.1

Description

For the JetMove 208-480, an optional integrated Ethernet interface can be ordered
(item: JM-208-480...-OEM). This option lets you address the JetMove 208-480 from
the controller via Ethernet instead of the JX2 system bus.

12.2

Description of Connections

The digital servo amplifier JetMove 208-480...-OEM is connected with the Ethernet
by a RJ45 socket (X71).

There are two types of interconnecting cables used for 10/100 MBit/s twisted pair
Ethernet:

• 1:1 straight-through twisted pair cables
• Crossover cables (transmitting and receiving lines are crossed)

Functional Equipment

1 Ethernet interface

10/100 MBit/s, TX

10-pin DIP switch for the lower 8 bits of
the IP address and of various operating
modes

RUN / STOP / LOAD

LED for status indication

RUN / ERR

Summary of Contents for JetMove 208-480





























































































































Search results

Summary of Contents for JetMove 208-480

Reviews:

Jetter JetMove 208-480, User Manual, Page: 93 / 124

Search results

Summary of Contents for JetMove 208-480

Reviews: