JetCat SPH5 Instruction Manual Download Page 44

Page: 44 / 60

Menu Structure

All similar data and running parameters are grouped in separate menus. Menus can be
displayed and their values modified (where accessible), by using the GSU.

Menu Selections

•

Run menu

•

MIN/MAX menu

•

RC-Check menu

•

Info menu

•

STATISTICS

•

Test Functions

•

Limits menu

•

Rotor speed Menu

Selecting a Menu

The corresponding keys (hot keys) can directly select the “Run”, “Info”, “MIN/MAX”, or
“Limits” menus. An alternate method is to press and hold the

Select Menu

key and use

the

◄

- /

►

keys for selecting.

Note:

this method is the only access to all menus.

Change Values / Items

In order to change an indicated value, press and hold the

Change Value/Item

key while

using the

◄

- /

►

keys to alter its value. An arrow (

→

) will appear in front of the

value, if it can be changed.

Important Note for

Min/Max

and

Info

values->

1. After the turbine has started and stabilized, the Min/Max values are reset. This

makes the Min/Max values correct for the actual run time of the turbine not
including the startup values.

2. When the turbine stops, the Min/Max values are copied to the Info menu’s “Last

values”.

Summary of Contents for SPH5




























































Search results

Summary of Contents for SPH5

Reviews:

Related manuals for SPH5

Brands by name

Popular brands

JetCat SPH5, Instruction Manual

Search results

Summary of Contents for SPH5

Reviews:

Related manuals for SPH5

Brands by name

Popular brands