background image

 

Minibeast Cordless 

This document is protected by copyrights. 

Copying, using, or distributing without permission of JEI Drilling & Cutting Solutions is prohibited. 

20 

6. ENVIRONMENTAL PROTECTION 

In  accordance  with  the  European  Directive  2012/19/EU,  this  device  is 

marked with the symbol of the crossed-out waste bin. This marking means 

that the equipment must not be disposed of with other household waste after 

the service life. The user must return the product to a collection point for used electrical 

and electronic equipment. The collectors of used equipment, including local collection 

points,  shops  and  municipal  units  create  an  appropriate  system  for  returning  such 

equipment.  Correct  handling  of  used  electrical  and  electronic  equipment  helps  in 

avoiding damage to health and the environment, which may result from the presence 

of dangerous components and incorrect storage and processing of such equipment. 

 

In  accordance  with  the  European  Directive  2006/66/EC,  the  batteries  are 

marked  with  the  symbol  of  the  crossed-out  waste  bin.  Below  this  symbol 

there may be a chemical symbol of heavy metal present in the battery, if its 

percentage is above: 0.0005% for mercury (Hg), 0.002% for cadmium (Cd), 0.004% 

for  lead  (Pb).  Batteries  must  not  be  disposed  of  with  household  waste  and  WEEE 

waste. The user must return the battery to a collection point for used batteries. Before 

returning the battery, discharge it*, remove it from the device and protect the contacts 

with insulating tape. Returning the battery to the collection point reduces the negative 

impact  of  its  hazardous  substances  on  human  health  and  the  environment,  and 

enables the recovery of raw materials and plastics in the recycling process. 

refers to undamaged batteries 

Summary of Contents for Minibeast Cordless























Reviews: