manualshive.com logo in svg

JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36, Operator'S Manual

Share
Download
JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36 Operator'S Manual Download Page 31

WWW.JEIUK.COM 

RAILBEAST RDP-36 

This document is protected by copyrights. 

Copying, using, or distributing without permission of Ansa Group Ltd is prohibited.

 

31 

5. DECLARATION OF CONFORMITY 

 

 

EC Declaration of Conformity  

 

We 

 

JEI DRILLING & CUTTING SOLUTIONS LTD 

UNIT 21 EMPIRE BUSINESS 

ENTERPRISE WAY 

BURNLEY, LANCASHIRE, BB12 6LT

 

 

declare with full responsibility that: 

 

RAILBEAST RDP-36 Petrol Rail Drilling Machine 

 

is manufactured in accordance with the following standards: 

•

  EN ISO 12100:2012 

and satisfies safety regulations of the guideline 2006/42/WE. 

 

 

Person authorized to compile the technical file: 

David McFadden, Unit 21 Empire Business Park, 

Burnley 

 

 

 

Burnley, 12

th

 February 2020 

___________________________ 

 

 

David McFadden 

 

                                                                                                         Managing Director 

Summary of Contents for RAILBEAST RDP-36


































Reviews:

No comments

Brands by name

Popular brands

Load more brands