www.jeffersontools.com
7L MANUAL
EXTRACTOR
JEFLUEXTM07
FEATURES
1. EQUIPMENT OVERVIEW
7ltr capacity
26mm suction port
4, 6, 8, 10mm x 1 Metre suction probes
Made from Acrylonitrile-Butadiene-Styrene thermoplastic polymer
material with Aluminium inflator
Strong and durable with strong resistance to heat and chemicals.
Suitable for the extraction of all types of engine, transmission and
lubricating oils from cars, motorcycles, marine engines, stationary
engines and industrial machinery
Also suitable for low viscosity fluids such as water, and
draining fish-tanks, basins, baths, cisterns, sinks etc
User Manual
v.1.1
JEFLUEXTM07
3. SAFETY
WARNING!
Ensure health & safety, local authority, and general workshop practice regulations are strictly adhered to when using this equipment.
Familiarise yourself with the extractors application and limitations, as well as the specific potential hazards relating to this product.
Ensure the extractor is maintained in good condition.
Replace or repair damaged parts using only genuine parts. Non authorised parts will invalidate the warranty.
Unit may be used only to extract engine or transmission oils, or similar NON-Corrosive fluids. Unit may also be used for the transfer of water.
Ensure safety eye protection and protective clothing are worn when using this product.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
Dispose of waste liquids in accordance with local authority regulations.
DO NOT store fluids in the JEFLUEXTM07 container. Once used to extract fluid, it must be emptied into an approved receptacle.
DO NOT use to extract hazardous or harmful chemicals, solvents, petrol, diesel, kerosene, alkaline or acids. If by chance such fluids are
used in the unit, it must be immediately drained and thoroughly cleaned. Use with prohibited fluids will invalidate your warranty.
DO NOT dismantle, tamper or adapt the extractor for any purpose other than for which it is designed.
DO NOT use the unit if it has been dropped or mishandled, check the unit to ensure there is no damage.
DO NOT store in areas of high temperature, direct sunlight, rain or snow.
Keep the extractor clean and store in a safe dry location.
1
4
5
2
3
1
Pump handle
2
Pump inlet
3
Vacuum release valve
4
Probe storage holder
5
7 Litre capacity tank
2. OPERATING INSTRUCTIONS
2.1 Ensure the vehicle is on level ground and run the engine for approximately 5 minutes to warm the oil and allow any contaminants
within the oil to thoroughly mix and turn the engine off.
2.2 Remove the vehicle’s oil dipstick.
2.3 Select and insert the appropriate diameter probe into the dipstick hole until it reaches the bottom of the sump
2.4 Connect the extension tube to both the pump inlet and probe
2.5 Raise the handle to its highest limit and pump it fully several times to create a vacuum which will automatically begin to extract the oil/fluid.
Observe the oil/fluid as it rises up the chamber and stop pumping when the fluid is 6”(150mmm) from the top. The unit will continue to fill
and will automatically shut off when the internal float valve operates. DO NOT continue to pump after the unit has shut off as this may result
in liquid entering the inner pump chamber. If this should occur refer to section 4.8 on how to expel fluid from the pump.
2.6 Once completed, remove the main suction tube from the pump, pour the oil/fluid into a suitable container (the unit can be tipped upside
down to facilitate emptying) and dispose of it in accordance with local authority regulations.
2.7 Before using the pump again press the vacuum release valve for 5 seconds to release the vacuum within the pump. This valve is situated on
the top of the unit underneath the handle.
2.8 In the event of fluid entering the inner pump chamber it can be expelled from the unit as follows. Firstly press the vacuum release valve for
5 seconds to release the vacuum within the pump. Seal off the fluid entry/pouring hole by placing your hand over it, then pump the handle
up and down several times. Any fluid that has entered the pump will be expelled from the air valve on the underside of the unit.
OTHER FLUIDS
2.9 Select and insert the appropriate diameter probe into the fluid to be drained.
2.10 Connect the main suction tube to both the pump inlet and probe.
2.11 The operation of the extractor is the same as described in sections 2.6 to 2.8
