background image

28

GETTING TO KNOW YOUR VEHICLE

 

NOTE:

If the brake is pressed and the ignition is placed in 

the RUN position with an EVSE connected to the 

vehicle, the instrument cluster display will not 

display the READY state. When the Electric Vehicle 

Supply Equipment (EVSE) is unplugged from the 

vehicle, the vehicle will go into the READY state. If 

the vehicle is not shifted out of PARK 30 minutes 

after being unplugged, the vehicle will disable the 

READY state. After an additional 30 minutes with 

no change in ignition status, the ignition will turn 

off and the vehicle will power down.
For more information on normal starting, see  

Ú

page 44.

REMOTE START — IF EQUIPPED   

NOTE:

Remote Start while the vehicle is plugged in may 

not always start the engine.

This system uses the key fob to start

the vehicle conveniently from outside

the vehicle while still maintaining 

security. The system has a range 

of 328 ft (100 m).

Remote Start also activates the Climate Control 

system in temperatures above 80°F (26.7°C),

and the heated seats (if equipped) and heated 

steering wheel (if equipped) in temperatures 

below 40°F (4.4°C).
NOTE:

Obstructions between the vehicle and key fob may 

reduce this range.

H

OW

 T

O

 U

SE

 R

EMOTE

 S

TART

All of the following conditions must be met before 

the vehicle will remote start:

Gear selector in PARK

Doors closed

Hood closed

Swing gate closed

Hazard switch off

Brake switch inactive (brake pedal not pressed)

12 Volt battery at an acceptable charge level

Key fob Panic button not pushed

System not disabled from previous Remote 

Start event

Vehicle Security system indicator flashing

Ignition in OFF position

Fuel level meets minimum requirement

All removable doors must not be removed

Malfunction Indicator Light (MIL) is off while the 

vehicle’s propulsion system is active

WARNING!

Do not start or run an engine in a closed 

garage or confined area. Exhaust gas contains 

Carbon Monoxide (CO) which is odorless and 

colorless. Carbon Monoxide is poisonous and 

can cause serious injury or death when 

inhaled.

Keep key fobs away from children. Operation 

of the Remote Start system, windows, door 

locks or other controls could cause serious 

injury or death.

22_JL_H_SU_EN_USC_t.book  Page 28  

Summary of Contents for WRANGLER 4Xe 2022

























































































Reviews: